VALOX(沙伯基础)K4530/PBT热塑性聚酯/物性表参数

日期：2020-04-20 01:33:38 编辑：科思德塑胶来源：科思德塑胶浏览：341

沙伯基础创新塑料SABIC的VALOX K4530 PBT是一种加15%玻璃增强PBT，水解稳定，高流量，汽车连接器。

以下是VALOX(沙伯基础)K4530/PBT热塑性聚酯/物性表参数

PROPERTIES	TYPICAL VALUES	UNITS	TEST METHODS
MECHANICAL
Tensile Stress, yld, Type I, 5 mm/min	103	MPa	ASTM D 638
Tensile Stress, brk, Type I, 5 mm/min	103	MPa	ASTM D 638
Tensile Strain, yld, Type I, 5 mm/min	4	%	ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min	4	%	ASTM D 638
Tensile Modulus, 5 mm/min	3550	MPa	ASTM D 638
Flexural Stress, brk, 1.3 mm/min, 50 mm span	150	MPa	ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span	4640	MPa	ASTM D 790
Tensile Stress, yield, 5 mm/min	98	MPa	ISO 527
Tensile Stress, break, 5 mm/min	98	MPa	ISO 527
Tensile Strain, yield, 5 mm/min	3.1	%	ISO 527
Tensile Strain, break, 5 mm/min	3.1	%	ISO 527
Tensile Modulus, 1 mm/min	5250	MPa	ISO 527
Flexural Stress, yield, 2 mm/min	150	MPa	ISO 178
Flexural Stress, break, 2 mm/min	150	MPa	ISO 178
Flexural Modulus, 2 mm/min	4750	MPa	ISO 178
IMPACT
Izod Impact, unnotched, 23°C	400	J/m	ASTM D 4812
Izod Impact, notched, 23°C	58	J/m	ASTM D 256
Izod Impact, unnotched 80104 +23°C	30	kJ/m²	ISO 180/1U
Izod Impact, notched 80104 +23°C	7	kJ/m²	ISO 180/1A
THERMAL
HDT, 0.45 MPa, 3.2 mm, unannealed	218	°C	ASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed	193	°C	ASTM D 648
Vicat Softening Temp, Rate B/120	205	°C	ISO 306
PHYSICAL
Specific Gravity	1.41	-	ASTM D 792
Mold Shrinkage, flow, 3.2 mm	0.7-0.9	%	SABIC method
Mold Shrinkage, xflow, 3.2 mm	1-1.2	%	SABIC method
Melt Volume Rate, MVR at 250°C/2.16 kg	17	cm³/10 min	ISO 1133
AFTER 40 CYCLES, SIMILAR TO USCAR-2, CLASS III
Tensile Stress, brk, Type I, 5 mm/min	82	MPa	ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min	2.5	%	ASTM D 638
Flexural Modulus, 1.3 mm/min, 50 mm span	4520	MPa	ASTM D 790
Flexural Strain, 1.3 mm/min, 50 mm span	9.7	%	ASTM D 790
Instrumented Impact, Total Energy, 23°C	6	J	ASTM D 3763
PROPERTIES AFTER 1008 HOURS AT 125?C
Tensile Stress, brk, Type I, 5 mm/min	98	MPa	ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min	4	%	ASTM D 638
Flexural Modulus, 1.3 mm/min, 50 mm span	4820	MPa	ASTM D 790
Flexural Strain, 1.3 mm/min, 50 mm span	7	%	ASTM D 790
Instrumented Impact, Total Energy, 23°C	5	J	ASTM D 3763
AFTER 40 CYCLES, SIMILAR TO USCAR-2, CLASS IV
Tensile Stress, brk, Type I, 5 mm/min	89	MPa	ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min	2.3	%	ASTM D 638
Flexural Modulus, 1.3 mm/min, 50 mm span	5100	MPa	ASTM D 790
Flexural Strain, 1.3 mm/min, 50 mm span	6	%	ASTM D 790
Instrumented Impact, Total Energy, 23°C	4	J	ASTM D 3763
PROPERTIES AFTER 1008 HOURS AT 155?C
Tensile Stress, brk, Type I, 5 mm/min	4812	MPa	ASTM D 638
Tensile Strain, yld, Type I, 5 mm/min	97.2	%	ASTM D 638
Flexural Modulus, 1.3 mm/min, 50 mm span	0	MPa	ASTM D 790
Flexural Strain, 1.3 mm/min, 50 mm span	3.8	%	ASTM D 790
Injection Molding
Drying Temperature	60-75	°C
Drying Time	4-6	hrs
Drying Time (Cumulative)	8	hrs
Maximum Moisture Content	0.05	%
Melt Temperature	250-265	°C
Nozzle Temperature	245-260	°C
Front - Zone 3 Temperature	250-265	°C
Middle - Zone 2 Temperature	245-260	°C
Rear - Zone 1 Temperature	240-255	°C
Mold Temperature	65-90	°C
Back Pressure	0.3-0.7	MPa
Screw Speed	50-80	rpm
Shot to Cylinder Size	40-80	%
Vent Depth	0.025-0.038	mm

温馨提示：
本物性表参数提供者不承担任何法律责任，建议在选择材料前，就数据值与塑胶材料厂商进行验证。版权归原作者所有，如有侵权请立即与我们联系.

上一页：VALOX(沙伯基础)K3501/PBT热塑性聚酯/物性表参数下一页：VALOX(沙伯基础)K4560/PBT热塑性聚酯/物性表参数

返回首页返回物性参数列表

VALOX(沙伯基础)K4530/PBT热塑性聚酯/物性表参数

热门文章

推荐文章